Cavetto ← Evil Melon home

You bring the bowls.

Cavetto will prescribe the spoon that gets every last bit out.

A worried stick figure holds up a giant spoon over a tiny bowl, while a banana screams in horror.

Bowls (receiving vessels)

All measurements are in millimetres. Enter rim, well and sag, and the cavetto base curve (CBC) is estimated for you. If you traced the cavetto from a photo, type that value into the CBC column to override the estimate.

NameSetRDWDSAGCBC overrideFitted CBC

Spoons (scooping instruments)

Enter bowl length (tip to heel) and bowl width. The tip base curve (TBC) is estimated from an ellipse, so egg-shaped tips come out a little blunter than they really are. Use the override column if you measured the tip from a photo.

NameSetBLBWTBC overrideFitted TBCToricity

Data

The CSV can also be copied or pasted here. Columns: type, name, set, RD, WD, SAG, CBC, BL, BW, TBC.

How to take a good photo

(tap to hide or show)

The tap-measure is only as good as the photo. Each example below shows roughly what your photo should look like.

card camera at rim height, ~1 m back, zoom 2× rim level
Bowl A · silhouette (quick)
  • Put the bowl on the very edge of a table in front of a plain, light wall.
  • Stand a card on its long edge, touching the bowl at its widest point.
  • Get the lens level with the rim, so the rim looks like a flat line, not an ellipse.
  • This photographs the outside, so enter the wall thickness below and the app will subtract it.
20c wire pressed into bowl, lifted out, laid flat shot from directly above
Bowl B · inner profile (most accurate)
  • Press a bendable wire into the bowl from rim to rim, through the centre. Solder, a coat-hanger or a pipe cleaner all work. A profile gauge from a hardware store is even better.
  • Lift it out carefully and lay it flat on white paper, next to a coin or card.
  • Photograph from directly overhead, then tap the points on the wire exactly as you would on a bowl.
  • Set the wall thickness to 0, because this method already measures the inside.
card phone directly overhead, parallel to the table
Spoon · top view
  • Lay the spoon bowl-up on plain white paper with the card flat beside it.
  • Hold the phone directly overhead, about 30 cm up, and parallel to the table.
  • Diffuse light, such as from a window, helps keep glare off the shiny metal and the edge crisp.
  • One spoon per photo, filling about half the frame.
angled: rim is an ellipse card far behind the bowl also avoid: glare, close-ups, cropped edges
Avoid
  • Shooting from above the rim. The bowl's depth shrinks, and its bend looks tighter than it really is.
  • A reference object nearer to or further from the camera than the item. Every measurement will be scaled wrong.
  • Close-ups with the phone's wide lens. Step back and zoom instead.
  • Harsh glare that hides the spoon's edge.

Tap-to-measure

Your photo never leaves your device, because everything is calculated in your browser. Put a reference object in the same plane as the item. For bowls, shoot side-on at rim height from about a metre back, then zoom in, which keeps perspective distortion small.

Zoom
Load a photo to begin.

Readings

No readings yet.

Fitting matrix

The numbers are the Spoon Compatibility Index (SCI, 0–100). Each bowl's best spoon is outlined. Colour shows the fit: alignment steep flat

Prescriptions by bowl

Shopping prescription

Bowl: side profile

RD SAG CBC R1R2 W1W2A C1–C5: cavetto trace points

Tap order: reference ×2 → R1, R2 (rim lip) → W1, W2 (where the flat well ends) → A (lowest point of the well) → 3–5 points tracing the cavetto on one side.

Spoon: top view

TBC T S1 S2 B1 B2 H BL

Tap order: reference ×2 → T (tip apex) → S1, S2 (tip shoulders, about 45° round from the apex) → B1, B2 (widest points) → H (heel, where the bowl meets the neck).

Glossary

Rim / lip
The top edge of the bowl. RD is the rim diameter, measured across the lip.
Well
The flat floor inside the bowl (a real crockery term). WD is the well diameter.
Cavetto
The concave bend between the well and the wall (a real crockery term). It's where soup hides, and it's what this app is named after.
CBC
Cavetto base curve: the radius of that bend in mm. The term is borrowed from contact lens base curves.
SAG
Sagittal depth: from the plane of the rim down to the well apex, the same way a contact lens's depth is measured.
Tip / heel
The front point of the spoon's bowl, and the back of the bowl where it joins the neck (real cutlery terms).
TBC
Tip base curve: the radius of the spoon's tip seen from above.
Toricity
Bowl length ÷ bowl width. About 1.0 is spherical (round soup spoon), and 1.4 or more is toric (oval spoon).
D
Curvature power in dioptres, using the keratometric formula 337.5 ÷ radius (mm). Higher means tighter.
Fit ratio
TBC ÷ CBC. Between 0.6 and 1.0 is an alignment fit, also called “on K”. Under 0.6 is a steep fit: it reaches the corner, but you need many small scrapes. Over 1.0 is a flat fit: the spoon bridges the cavetto, causing peripheral soup pooling.
SCI
Spoon Compatibility Index from 0 to 100. It peaks at a fit ratio of 0.8, penalises flat fits harder than steep ones, and takes points off when a spoon is too long for a small bowl.

The principle is real enough: some patents specify a spoon tip radius equal to the radius of the bowl's bend. Everything else here is earnest pseudo-science. Cavetto is not a registered health profession.